Comparative Analysis of Properties in Chairside Silicone Denture Liners versus Heat-Cured Molloplast-B: An In-Depth In Vitro Evaluation.

BACKGROUND We investigated the bond strength, tensile strength, and water absorption properties of 4 widely used chairside silicone long-term denture soft lining materials and compared properties with those of heat-cured silicone material. MATERIAL AND METHODS Four chairside materials (GC Reline Soft, Mucopren Soft, Sofreliner Soft, and Elite Soft Relining) and a heat-cured silicone material (Molloplast B) were investigated. For tensile and shear bond strength and tensile strength, samples were prepared according to the manufacturers' instructions and the testing machine used. For water absorption, IOS 1567 was followed to prepare specimens. Bond strengths were measured using a Lloyd Instruments materials testing machine. Ten specimens for each test were prepared for each soft liner, except for water absorption and solubility tests, for which only 5 specimens were prepared. ANOVA, Bonferroni, and Kruskal-Wallis tests were used to compare values of materials and assess changes over time. RESULTS There was strong evidence of differences in the properties between materials. GC Reline Soft showed comparable tensile bond (1.4±0.6 MPa), shear bond (1.1±0.4 MPa), tensile strength (5.44±0.98), water absorption (0.92±0.2 µg/mm³), and solubility values (0.3±0.2 µg/mm3) to that of Molloplast B (1.4±0.4; 1.6±0.5; 4.53±0.9 MPa, 1.7±0.3, and 1.0±0.3 µg/mm³, respectively). The water solubility of Sofreliner Soft was significantly lower (1.5±0.8 µg/mm³) than that of Molloplast B. CONCLUSIONS There were significant differences between some properties of 4 chairside denture soft lining materials and that of Molloplast B, which had higher shear and tensile bond strength than chairside denture silicone soft lining materials but had the highest water solubility.

Effects of Blood Contamination and Decontamination Protocol on Reverse Torque Value of Abutment Screws in Dental Implants: An In Vitro Study.

Background and Objective: Loosening of abutment screws in dental implants is a mechanical complication that affects prosthetic treatments and hence, patient satisfaction. Blood contamination of abutment screws may play a role in this phenomenon. However, only limited research attention has been given to this issue. In the present study, we determined the effect of blood contamination and decontamination protocol on the reverse torque value (RTV) of abutment screws. Materials and Methods: A questionnaire-based survey was sent to 210 implantologists requesting feedback on their attitude to the blood contamination issue and the decontamination protocols used. The survey responses were used in a selection of the decontamination solutions that were used in the subsequent in vitro study on the effects of blood decontamination protocol on the RTV of abutment screws. Thus, three study groups were used (n = 20 abutment screws in each group): Group 1 (control group; blood-contaminated screws); Group 2 (screws decontaminated with 5.25% sodium hypochlorite (NaOCl) solution); and Group 3 (screws decontaminated with normal saline solution (0.9%)). Then, each of the connections were subjected to thermocycling, and RTVs of the screw were measured using a digital torque meter. Intragroup and intergroup RTVs were analyzed for significance using analysis of variance (ANOVA) and Tukey's honestly significant difference (HSD) tests. Results: 48% of the implantologists responded to the survey; 80% of them were concerned with blood contamination in the implant connection, especially before abutment loading and 85% of them used either chlorhexidine solution or normal saline solution as the decontamination agent. The mean RTV for Group 2 screws (30.27 ± 2.8 N.cm) was significantly greater than that for Group 3 screws (26.02 ± 1.99 N.cm) which, in turn, was significantly greater than that for Group 1 screws (23.64 ± 1.84 N.cm). Conclusion: Decontamination of blood-covered connections using 5.25% NaOCl solution or normal saline solution restores the RTV of abutment screws. This finding may have clinical relevance in that the decontaminated screws may contribute to the low incidence of screw loosening and, ultimately, improved patient satisfaction.

Effects of the Cervical Marginal Relocation Technique on the Marginal Adaptation of Lithium Disilicate CAD/CAM Ceramic Crowns on Premolars.

AIM AND OBJECTIVE: To evaluate the effect of cervical margin relocation (CMR) for crowns designed using CAD/CAM technology and fabricated from lithium disilicate (e.max, CAD) before and after aging; and to compare the fracture forces and failure type of the tested crowns. MATERIALS AND METHODS: Mesio-occluso-distal(MOD) cavities 1 mm above the cementoenamel junction(CEJ) were prepared on 40 maxillary first premolars. The teeth were divided into four groups. In group A, all cervical margins (CM) were located 1 mm above the CEJ. However, in both mesial and distal proximal boxes of groups B, C, and D, in addition to the MOD cavities, the CMs were extended 2 mm on both sides below the CEJ apically to simulate the CMR technique. In group B, the mesial and distal proximal boxes were filled with flowable composite, while for group C and group D, specimens were filled with composite resin fillings. To simulate the CMR technique, the cavities were filled with composite layers of 3 mm in two increments. Using the CAD/CAM system, 40 standard crowns were prepared on premolars, then cemented using a dual-curing adhesive cement. Assessments of the marginal integrity of interfaces of the proximal boxes of the cemented crowned teeth were recorded. Statistical differences between groups were analyzed using the ANOVA and Bonferroni's posthoc test. RESULTS: The first null hypothesis was accepted since no statistically significant differences were found in marginal integrity before and after aging (p>0.05), while the second was partially rejected since different fractured force values were recorded and a significant difference was detected between group D and group B. The third hypothesis was rejected because the catastrophic fracture rate was the highest among the four groups. CONCLUSION: The implementation of CMR before and after aging had a good effect on the marginal integrity of CM relocation. The CMR technique with resin luting cement of lithium disilicate crowns is effective and recommended for the restoration in deep proximal boxes of premolars or posterior teeth. CLINICAL SIGNIFICANCE: CAD/CAM-generated e. max all-ceramic crowns with composite as the CMR enable the reconstruction of severely destroyed teeth irrespective of the position of the cavity margins.

Assessment of Color Stainability of Computer-Aided Design and Computer-Aided Manufacturing (CAD/CAM) Ceramic Materials After Hot and Cold Coffee Immersion at Different Time Intervals.

BACKGROUND This spectrophotometric study assessed the color stability of CAD/CAM restorative materials with different exposed surfaces following staining by hot Arabic Qahwa and cold coffee. MATERIAL AND METHODS Ninety-six specimens were fabricated from 3 different CAD/CAM ceramic materials: Vita Suprinity (Vita-S), Vita Enamic (Vita-E), and Vitablocs Mark II (Vitablocs-MII). We divided 32 specimens for each group into glazed or polished surfaces, with 16 specimens in each group, then subdivided them according to staining materials: Arabic Qahwa and Frappuccino Cold Coffee. Color of specimens was measured during immersion in staining materials (BEFORE) as baseline with (Vita classic) and (L, a, b), for average color changes (ΔE00), then remeasured after 2, 4, and 12 weeks, and described as 1st, 2nd, and 3rd measurements for VITAPAN Classic shade and T1, T2, and T3 for ΔE00 values using the CIE L*a*b* equation. We performed ANOVA and then post hoc testing. RESULTS We found significant differences in ΔE00 values during immersing in hot Arabic Qahwa and cold coffee for tested materials in glazed or polished specimens. Polished specimens of Vita-S and Vita-E had the highest color changing and staining compared to glazed surfaces. Vitablocs-MII had the best color stability through immersion periods. Moreover, there were changes in relation to VITAPAN Classic shade guide for both Vita-S and Vita-E specimens during different immersion periods. CONCLUSIONS Coffee caused staining and contamination of ceramic material. Values of ΔE00 for tested ceramic materials were significantly different but were within the clinically acceptable range. Polished specimens showed higher staining; therefore, we highly recommend re-glazing of ceramic restorations to maintain color stability.

Dental Anxiety and Fear among Patients in Jazan, Kingdom of Saudi Arabia: A Cross-sectional Study.

AIM: The current study aims to address the patient's dental anxiety (DA) And dental fear (DF) under the treatment of a general practitioner (GP) among different parameters. MATERIALS AND METHODS: The cross-sectional study included 500 patients recruited from different clinics in Jazan, Saudi Arabia. Data were collected through a questionnaire-based form consisting of three parts; the first part was personal and demographic questions whereas the second and third parts were a modified dental anxiety scale (MDAS) and a dental fear survey (DFS) to measure DA and DF among patients. Spearman's correlation was used to measure the relation between DA and DF as well as Chi-square tests and logistic regression analyses for analyzing the effect of each variable on DA and DF. RESULTS: All patients fulfilled their eligibility criteria. A high percentage was found in moderate anxiety (36.8%) as well as in moderate fear (46.2%) among different anxiety and fear scales. The association between DA and DF was positively significant (p <0.01). There was a significant effect of gender, age, education, khat use, marital status, monthly income, and type of clinic on patients' DA and DF. CONCLUSIONS: There is a positive relation between MDAS and DFS, thus the DA affects the DF. Female patients had a lower DA and DF than male patients. Furthermore, the government clinics had the highest DA and DF prevalence levels for patients. Moreover, the high school-graduated patients seem to have a high DA and DF vs other patient educational levels. CLINICAL SIGNIFICANCE: It would be beneficial to include an educational training program about psychological patient management in the study curriculum as well as to be offered as a special course to newly graduated dentists. This modification will aid to improve the GPs to get rid of DA and DF patients. How to cite this article: AlDhelai TA, Al-Ahmari MM, Adawi HA, et al. Dental Anxiety and Fear among Patients in Jazan, Kingdom of Saudi Arabia: A Cross-sectional Study. J Contemp Dent Pract 2021;22(5):549-556.

Use of a Rotational Flap with Soft Tissue Graft and Tunneling Technique for Ovate Pontic Site Development for a Highly Esthetic Outcome: A Case Report.

AIM AND OBJECTIVE: The objective of therapy was to replace the missing teeth with a restoration that closely adhered to the natural teeth and soft tissue contour to provide an esthetic outcome. CASE DESCRIPTION: A 19-year-old male reported a failed fixed partial denture (FPD) in the maxillary left central incisor. The abutment extended to the maxillary right central incisor and the maxillary left lateral incisor. Radiographic examination revealed that the neighboring maxillary right central incisor abutment was nonrestorable. The treatment plan was the extraction of the maxillary right central incisor with socket preservation, modification of the pontic sites for placement of an ovate pontic for the replacement of the missing maxillary upper central incisors with an FPD with the maxillary lateral incisors serving as the abutment teeth. The pontic sites were corrected with a U-shaped flap extended 5 mm palatal from the mid-crestal line. The incision was avoided at the interdental papilla area. The facial flap was elevated. The facial soft tissue was vertically tunneled. The flap was flipped into the facial tunnel and stabilized with horizontal nylon matrix sutures. The surgical site was stabilized with a provisional FPD with an ovate pontic. The final restoration was a full zirconia facial veneered FPD. RESULTS: Surgical site showed significant healing with a natural emergence profile, and interdental papillae filling the gingival embrasure, showing no evidence of recession. At the 1-year follow-up, the gingival thickness improved and the pontic emergence profile was natural. A very stable result for soft tissue volume and interdental papillae were seen. CONCLUSION: According to the result obtained with rotational flap, it can be used for small anterior defects with promising results, without the need for bone graft procedures or additional tissue graft. CLINICAL SIGNIFICANCE: With proper case selection, the use of a rotational flap with a tunnel technique and an ovate pontic in the anterior esthetic region is an alternative treatment option that can successfully restore masticatory and esthetic function.